Juniper JN0-351 PDF Exam Questions:
How to Get Success in Juniper JN0-351 Exam:
- Avoid deceptive JN0-351 PDF Exam Questions.
- Focus on JN0-351 Questions (PDF) based on the latest exam syllabus.
- Make notes of Juniper JN0-351 PDF for better learning.
- Prepare from our latest Juniper JN0-351 PDF file and get success in first attempt.
Prepare Juniper JN0-351 Exam Within Short Time
Your knowledge and abilities are validated by passing the Juniper JN0-351 exam. Our PDF questions and answers will help you prepare for the JN0-351 exam in a short time because it includes questions similar to the real Juniper exam questions. After downloading the JN0-351 Juniper PDF exam questions, relevant to the actual exam, you can take a print of all questions and prepare them anytime, anywhere.
Realistic Scenario Based Juniper JN0-351 PDF Exam Questions:
Everyone wants to become certified Juniper Data Center Certification and improve his/her resume. You should practice with real JN0-351 questions. Students can benefit from the JN0-351 exam questions which are available in PDF format. The JN0-351 exam questions and answers are designed to match the criteria of the actual exam. If you use scenario-based Juniper JN0-351 questions you will have an extra potential to clear the exam on the first attempt.
Exhibit.
Which router will become the OSPF BDR if all routers are powered on at the same time?
See the explanation below.
In this scenario, all routers have the same priority of 1, so the router ID will determine the outcome of the election. The router IDs are shown in the exhibit as RID values. The highest RID belongs to R4 (10.10.10.4), so R4 will become the DR. The second highest RID belongs to R3 (10.10.10.3), so R3 will become the BDR.
Exhibit.
What is the management IP address of the device shown in the exhibit?
See the explanation below.
The management IP address of a device is the IP address that is used to access the device for configuration and monitoring purposes. It is usually assigned to a dedicated management interface that is separate from the data interfaces. The management interface can be accessed via SSH, Telnet, HTTP, or other protocols.
In the exhibit, the list of interfaces and their statuses shows that the management interface is me0. This interface has an admin status of up, a protocol status of inet, a local address of 172.23.12.100/24, and a remote address of unspecified. This means that the me0 interface is active, has an IPv4 address assigned, and is not connected to another device.
Therefore, the management IP address of the device shown in the exhibit is 172.23.12.100.
: [Management Interfaces Overview] : [Displaying Interface Status Information]
Which three protocols support BFD? (Choose three.)
See the explanation below.
BFD is a protocol that can be used to quickly detect failures in the forwarding path between two adjacent routers or switches. BFD can be integrated with various routing protocols and link aggregation protocols to provide faster convergence and fault recovery.
Other protocols that support BFD on Junos OS devices are:
IS-IS: BFD can be used to monitor the connectivity between IS-IS neighbors and trigger a state change if a failure is detected. BFD can be configured for both level 1 and level 2 IS-IS adjacencies, as well as for point-to-point and broadcast network types.
RIP: BFD can be used to monitor the connectivity between RIP neighbors and trigger a route update if a failure is detected. BFD can be configured for both RIP version 1 and version 2 protocols, as well as for IPv4 and IPv6 address families.
VRRP: BFD can be used to monitor the connectivity between VRRP routers and trigger a priority change if a failure is detected. BFD can be configured for both VRRP version 2 and version 3 protocols, as well as for IPv4 and IPv6 address families.
The protocols that do not support BFD on Junos OS devices are:
RSTP: RSTP is a spanning tree protocol that provides loop prevention and rapid convergence in layer 2 networks. RSTP does not use BFD to detect link failures, but relies on its own hello mechanism that sends BPDU packets every 2 seconds by default.
FTP: FTP is an application layer protocol that is used to transfer files between hosts over a TCP connection. FTP does not use BFD to detect connection failures, but relies on TCP's own retransmission and timeout mechanisms.
Exhibit.
The ispi _ inet. 0 route table has currently no routes in it.
What will happen when you commit the configuration shown on the exhibit?
See the explanation below.
The configuration also includes a rib-group statement, which is used to import routes from one routing table to another. A rib-group consists of an import-rib statement, which specifies the source routing table, and an export-rib statement, which specifies the destination routing table.
In this case, the rib-group name is inet-to-ispi, and the import-rib statement specifies inet.0 as the source routing table. The export-rib statement specifies ispi.inet.0 as the destination routing table. This means that the routes from inet.0 will be imported into ispi.inet.0.
Therefore, the correct answer is B. The inet.0 route table will be imported into the ispi.inet.0 route table.
1:Routing Instances Overview2:Virtual Routing Instances: [rib-group (Routing Options)]
Which statement is correct about graceful Routing Engine switchover (GRES)?
See the explanation below.
Reliable Source Of Preparation For Enterprise Routing and Switching, Specialist Exam.
We provide Juniper Data Center Certification certification questions along with answers to assist students in passing the Juniper Exam. You can enhance your Juniper JN0-351 preparation with the help of an online practice engine. Try out our Juniper JN0-351 questions because 98% of Examskit users passed the final JN0-351 exam in one go.